jump cable LINCOLN CONTINENTAL 1996 Customer Assistance Guide

/! WARNINGBatteries contain sulfuric acid which bumsskin, eyes, and clothing.If the acid touches someone's skin, eyes, or clothing,
immediately flush the area with water for at least 15
minutes. If someone swallows the acid, have him or
her drink lots of milk or water first, then Milk of
Magnesia, a beaten egg, or vegetable oil. Call a
doctor immediately.
To avoid damaging your vehicle or your battery, and
to avoid injury to yourself, follow these directions
for preparing your vehicle to jump-start and
connecting the jumper cables in the order they are
given. If in doubt, call for road service.
200Preparing Your Vehicle
1 .Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system. You
will damage your starting motor, ignition system,
and other electrical parts if you connect them to a
24-volt power supply (either two 12-volt
batteries in series,or a 24-volt generator set).
2.Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
3.Park the booster vehicle close to the hood of the
disabled vehicle. Make sure the vehicles do not
touch each other. Set the parking brake on both
vehicles and stay clear of the engine cooling fan
and other moving parts.
4.Check all battery terminals and remove any
excessive corrosion before you attach the jumper
cables.

5.Turn on the heater fan in both vehicles. Press the
DEFROST button. Turn off all other switches
and gauges.
Connecting the jumper cables
1. Connect one end of the first jumper cable to the
positive (+) terminal of the discharged battery.
(You can connect either jumper cable to the
positive (+) terminal, as long as you use the
same cable for both positive terminals.) Most
jumper cables have a red cable and a black cable.
The red cable is generally used for the positive
terminals and the black for the negative ones.
2. Connect the other end of the first cable to the
positive (+) terminal of the booster battery.3. Connect one end of the second cable to the
negative (-) terminal of the booster battery NOT
to the discharged battery.
4. Connect the other end of the second cable to a
good metallic surface on the engine or frame of
the disabled vehicle./! WARNINGDo not connect the end of the second cable tothe negative (-) terminal of the battery to bejumped. A spark may cause an explosion ofthe gases that surround the battery.201

Alternator mounting brace stud jumper cable
The engine with jumper cables
202 Booster battery

Jump-Starting
1.Make sure that the jumper cables are not in the
way of moving engine parts, then start the
booster vehicle. Run the engine at a moderate
speed.
2.Let the discharged battery charge for a few
minutes and then start the disabled vehicle. It
may take a couple of tries before the vehicle
starts. If the vehicle does not start after several
attempts, there may be a different problem.
3.When both vehicles are running, let them idle
for a few minutes to charge the discharged
battery.
Removing jumper cables
1.Always remove the jumper cables in the
reverse order. Remove the negative (-) end of
the jumper cable from the metallic surface on
the engine or frame of the disabled vehicle.2.Remove the negative (-) cable from the booster
battery.
3.Remove the positive (+) cable from the booster
battery.
4.Remove the other end of the positive (+) cable
from the discharged battery.
After the vehicle is started, let it idle for a while to let
the engine "relearn" its idle conditions. Drive it
around for a while with all electrical accessories
turned off to let the battery recharge. You may need
to use a battery charger to fully recharge the
battery.
If you need to replace your battery, see Battery in the
Servicing Your Vehicle chapter.
203

Headlamps (continued).................................I.............................
cleaning...............................................83Idle.............................................................
daytime running lights..........................81relearning.........................................253
flashing................................................90speed.................................................45
high beam............................................90Ignition......................................................
replacing bulbs...................................277chime.................................................42
turning on and off................................82positions of the ignition......................41
warning chime.....................................58removing the key...............................42
Head restraints.......................................114Infant seats (see Safety seats).................27
Heated mirrors.......................................127Instrument panel, location of components .70
Heating........................................................Interval wipers........................................91
electronic automatic temperature...............................................................................
control system...................................71J.............................
High beams, indicator light.......................58Jack, operation.....................................207
Hood............................................................Jump-starting your vehicle..........................
latch location...............................234,235attaching cables................................201
lubrication specifications....................289disconnecting cables.........................203
release lever.......................................234K...............................
working under the hood.....................233Keyless entry system...................................
Horn........................................................93locking and unlocking doors............102
....................................................................programming entry code..................103
314